Logo
Doprava do: CZ

Přihlásit se
Stav objednávky

Muc-otevrený/á/é Tubeless Stealth Tag Holder sada

vč. 21% DPH Doprava zdarma do CZplus přepravní náklady.
Množství
PŘIDAT DO NÁKUPNÍHO KOŠÍKU
Pouze online a Click & Collect
V současné době je k dispozici v obchodě Kronberg
Číslo výrobku
Výrobce-č.výrobku
Varianty
Číslo výrobku výrobce na displeji
Muc-otevrený/á/é Tubeless Stealth Tag Holder sada 46030084 30,40€
Číslo výrobku výrobce
Vyberte variantu.

Mobile and unobtrusive theft tracker

The Muc-Off Tubeless Tag Holder offers a discreet way to install a tracker in your tubeless rear tire in conjunction with a Muc-Off tubeless valve, allowing you to track your bike in the event of theft and locate it using the Find My iPhone app .

Your tracker is housed in a protective 3-piece silicone and rubber valve mount. The Apple Air Tag and Muc-Off valves are optionally available.

assembly instruction

Attaching a tracker to the Tubeless Tag Holder:

Take the Tubeless Tag Holder out of the packaging and then carefully remove the pink silicone cap from the black rubber housing, followed by the internal connector.

Make sure the tracker is set up and connected to your iPhone app.

Take your tubeless valve and remove the valve cap, retaining ring and o-ring from the valve stem, then place the tubeless valve down into the hexagonal rubber slot in the black stem retainer. Pull the valve through from the side of the valve core until the base of the valve rests against the inner base of the retainer. (Keep the o-ring and locking ring until you mount the valve on your rim).

Place the inner plug over the hex opening to seal the tracker storage compartment.

Insert the tracker into the top of the connector with the battery cover facing down toward the base of the stem mount. It is best to press the tracker into the holder with both thumbs so that the side walls of the black rubber body come over the sides of the tracker.

Then carefully place the silicone top cover over the assembled tracker and storage compartment by turning it upside down and slowly pulling the cover over it until the entire compartment is covered.

Finally, select the appropriate rubber grommet for your rim type and slide this over the valve stem until the base rests against the underside of the tracker mount.

Suitable for the bike:

If using with an existing tubeless setup, deflate your tubeless tire, pull the tire off the bead and remove your tubeless valve.

Clean Before installing the Tubeless Tag Holder, clean the valve hole area on the inside of your rim with a clean microfiber cloth to remove excess sealant. (For stubborn sealant that needs to be removed, you can use our Glue & Sealant Remover).

Take your assembled tubeless tag holder with the valve installed and push the valve stem into the hole in the rim until it is all the way through. Then place the rubber O-ring on the valve stem and slide it all the way down until it meets the rim.

Thread the retaining ring onto the valve stem and tighten above the o-ring. This clamps between the retaining ring and the rim. While tightening the locking ring, press on the top of the Tubeless Tag Holder inside the rim and tighten until the locking ring is hand tight and the rubber o-ring is pushed out. That way you'll know you've created a good, airtight seal. (TIP - don't over-tighten as this may cause leakage. Finally, screw on whatever valve cap you want).

Reinstall your tire by starting at the tracker stem and making sure to slide the tire bead over the tracker base.

Use the valve core removal tool (integrated into the replacement cap) to remove the core and fill with tubeless puncture proof sealant and inflate to the pressure recommended by the tire manufacturer.

Mission accomplished, let's go!

If you are using the Tubeless Tag Holder with a brand new tubeless setup and tire, we recommend that you inflate the tire with your tubeless valve and attach the tire bead to the rim without installing the Tubeless Tag Holder first. This is because the Tubeless Tag Holder can limit the larger amount of air required for the initial tubeless setup. Then remove the valve and assemble the Tubeless Tag Holder using the assembly procedure and steps outlined above.

Note: Periodically remove the tracker from the mount and dry off excess tubeless sealant when replacing or topping up sealant. You may need to replace the battery in your tracker every 6 months to 1 year.

highlights

  • Easy to install
  • Optimized for use with tubeless Presta valves (44-60 mm) from Muc-Off
  • Robust mount - the tracker is well protected even in the event of heavy impacts and falls
  • Durable rubber stock attachment allows air and sealant to flow freely
  • The silicone top cover protects the tracker and the internal plug keeps tubeless sealant out
  • Does not block the tracker signal
  • The rattle-free design keeps the tracker securely in place
  • Weighs 7.5 g without AirTag -18.7 g with AirTag
  • Designed for use on rear wheels
  • Compatible with
    MTB tires (XC, Enduro Trail, Downhill, E-MTB)
    Gravel Tires (The narrowest recommended tire size is 38c wide)
    For road bikes with narrower tires or incompatible wheel types, please use the Muc-Off Secure Tag Holder
 
 

scope of delivery

  • 1 x Muc-Off Tubeless Stealth Tag Holder (see item description for details)
  • 2 x tubeless valve 44mm
  • 3 x valve feet
 
V současné době nabízíme tyto Manufacturer Info jen v česky

Über die Marke Muc-Off

V současné době nabízíme tyto Info o skupině položek jen v česky
Cenový alarm!
Chybička se vloudila?
Platí naše obchodní podmínky.
AJAX Loader Icon